Installing Hurricane Shutters On Vinyl Siding

Primer isn't necessary for vinyl shutters that are in good condition, because the paint will adhere to the vinyl surface without any problems. Be sure to leave space between the edge of the shutter and the window edge so your shutters can expand and contract as temperatures rise and fall.

Installing Hurricane Shutters On Vinyl Siding Hurricane Fabric

Attaching the shutter step 1 position the shutter along the side of the window or door.

Installing hurricane shutters on vinyl siding. (2) measure down 2″ from the top of the shutter and center on each side stile. And so as long as you’re careful about the way they attach, you certainly can have shutters on top of vinyl. Got to get creative on how to install shutters without drilling into siding.

Install your shutters have a helper hold a shutter up to the edge of your window. Once all the materials are gathered it is time to install the first shutter. (2) measure up 2″ from the bottom of the shutter and center on each side stile.

For wood, vinyl & aluminum. Mark the locations of the laps closest to the corners and middle of the shutter. Step 1, pull out the parts and lay them out on your driveway or lawn near the window they will be protecting.

If there’s a window sill, accommodate for it by only adding 4 inches to the height. Install board & batten shutters: Remove the shutter and drill a 1/8 inch diameter hole through the siding and into the wall at least 1¾ inches deep at the marks.

This is common in florida and getting more so along the gulf. A web direct brands site. With increasingly volatile weather conditions all year round and particularly violent storms defining hurricane season, this is the best option.

References (1) click to see full answer. Hurricane protection over vinyl siding/windows. If you put the shutters up, are they all going to be about the same size?

Use a hammer to gently tap the fasteners to snug the shutter to the siding. In a later step, you’ll add a mounting bracket on. Homeowners in the gulf south are turning to hurricane shutters for vinyl siding in a bid to limit the damage to their properties.

Run a bead of silicone caulk along the top of the header to seal. There should be a ½ inch space between the shutter and edge of the window. Step 2 lay shutter flat on work surface.

You do want to be careful not to squish the siding because, remember, the siding is somewhat soft. Attach the shutter reposition the shutter. Drive in one screw near the center of the header, then check it for level before driving in the remaining screws.

For vinyl and aluminum siding, using a ¼ inch diameter bit, drill a clearance hole through the siding only. Center the shutters by eye within the opening, and use wood shims to hold them in place on all four sides. Position the shutter to align its pilot holes with the holes in the siding.

For shutters 55 and over, use six shutter fasteners per shutter. Hold the shutter up next to the window in the location you desire. Drill through each hole in the siding and shutters to a depth of 3¼ inches, using the mark you made on the drill bit as a depth guide.

Place the decorative vinyl shutter face up on a flat work surface. If the vinyl shutters show signs of deterioration, severe weather damage, or pitting, then it may be a good idea to use a primer in order to seal these imperfections and provide a good base for the paint. Do not drill into the wall.

The follow pictures depict a typical hurricane shutter installation from start to finish. We have 7 days a week hurricane shutter installation support : The installation plan provided by contractor;

Overtightening fasteners during shutter installation can create warping or dimples on the surface of vinyl shutters Mark six (6) spots on each shutter (see drawing below). Installation procedures for mounting your hurricane panels.

And maybe that will get you where you want to go. Holes should be slightly larger than the screws. To make future installations easier it is wise to keep all these materials together in one place.

Begin by holding the header track horizontally above the window, making sure its bottom edge is flush with the window. Push shutter locks through the holes in the shutter and into the hole in the wall surface. Place shutter back on the house and.

Whether the concern is flying debris breaking windows or tree limbs crashing through the glass into the interior of. Set the shutters in place inside the window opening, lined up with each other at the top and bottom and flush with the brick facade. This will make step one much quicker in the event of a hurricane emergency.

You might also want to check with the local insurance agents. Electric drill, ¼ drill bit, 3⁄8 drill bit, hammer, and shutter fasteners. Drilling in the first tapcon screw.

(¼ carbide drill bit is required for stucco, hardboard, fiber cement, brick or masonry.) for shutters up to 55, use four shutter fasteners per shutter. And most of the shutter companies will sell those as part of the shutter, too, so you certainly can do that. Hold the shutter over your holes.

Drill holes at lap locations. • 3/16 metal drill bit (for structures with siding or wood structures) • 1/4 metal drill bit (in addition to one of the above drill bits) for To begin, measure each window and add 8 inches all the way around to the height and width.

Once you determine where you would like the shutter to be placed, use a pencil to mark the edge on the siding.

Vinyl Siding Siding Installation Soffit & Fascia Florida Jack